YwRobot Arduino LCM1602 IIC V1

Heute kamen meine LCDs aus Hongkong an die ich bei Ebay geschossen hatte.
Es handelt sich um die YwRobot Arduino LCM1602 IIC V1 LCDs. Da ich zur Zeit
auch ein größeres Projekt mache in dem ich eins brauche und ich PINs sparen möchte,
kam mir das Angebot ganz recht. Lange Rede kurzer Sinn, möchte nur jetzt hier schreiben
wie Ihr es anschließt um es zum laufen zu bringen.

YwRobotLCD-CU-450

LCD ———> Arduino
GND ———> GND
VCC ———> VCC 5 V
SDA ———> A4
SCL ———> A5
Ihr müsst dann noch die LiquidCrystal_I2C Library in eure Arduino IDE laden.
Sketch:
/*Example Software Sketch
 16 character 2 line I2C Display
 Backpack Interface labelled „A0 A1 A2“ at lower right.
 ..and
 „YwRobot Arduino LCM1602 IIC V1“
 Die meisten benutzen die Adresse  0x27, einige die 0x3F
 terry@yourduino.com
 Anschluesse:
 GND zu GND
 VCC zu 5V
 SDA zu A4
 SCL zu A5
 */
/*—–( Import needed libraries )—–*/
#include <Wire.h>  // Kommt mit der Arduino IDE
// Die LCD I2C Library gibt es hier:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/downloads
#include <LiquidCrystal_I2C.h>
/*—–( Declare Constants )—–*/
/*—–( Declare objects )—–*/
// set the LCD address to 0x27 for a 16 chars 2 line display
// A FEW use address 0x3F
// Set the pins on the I2C chip used for LCD connections:
//                    addr, en,rw,rs,d4,d5,d6,d7,bl,blpol
LiquidCrystal_I2C lcd(0x27, 2, 1, 0, 4, 5, 6, 7, 3, POSITIVE);  // Set the LCD I2C address
/*—–( Declare Variables )—–*/
//NONE
void setup()   /*—-( SETUP: RUNS ONCE )—-*/
{
  Serial.begin(9600);  // Used to type in characters
  lcd.begin(16,2);   // initialize the lcd for 16 chars 2 lines, turn on backlight
// ——- Quick 3 blinks of backlight  ————-
  for(int i = 0; i< 3; i++)
  {
    lcd.backlight();
    delay(250);
    lcd.noBacklight();
    delay(250);
  }
  lcd.backlight(); // finish with backlight on
//——– Write characters on the display ——————
// NOTE: Cursor Position: (CHAR, LINE) start at 0
  lcd.setCursor(0,0); //Start at character 4 on line 0
  lcd.print(„Hallo, Welt!“);
  delay(1000);
  lcd.setCursor(0,1);
  lcd.print(„HI!ganzprivat.de“);
  delay(8000);
// Wait and then tell user they can start the Serial Monitor and type in characters to
// Display. (Set Serial Monitor option to „No Line Ending“)
  lcd.clear();
  lcd.setCursor(0,0); //Start at character 0 on line 0
  lcd.print(„Oeffne Serial Mon“);
  lcd.setCursor(0,1);
  lcd.print(„Tippe irgendwas“);
}/*–(end setup )—*/
void loop()   /*—-( LOOP: RUNS CONSTANTLY )—-*/
{
  {
    // when characters arrive over the serial port…
    if (Serial.available()) {
      // wait a bit for the entire message to arrive
      delay(100);
      // clear the screen
      lcd.clear();
      // read all the available characters
      while (Serial.available() > 0) {
        // display each character to the LCD
        lcd.write(Serial.read());
      }
    }
  }
}/* –(end main loop )– */
/* ( THE END ) */

Autor: skippy

Hobbybastler, Tüftler, Ausprobierer :)

Ein Gedanke zu „YwRobot Arduino LCM1602 IIC V1“

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert

%d Bloggern gefällt das: